Comments

You must log in or register to comment.

reedstar1220 t1_it7oekm wrote

Most dishwashers have a float in the bottom of the tub. Possibly yours is faulty or obstructed in some way? Usually its just a plastic dome float with a electrical micro switch below the water.

3

HoneyBadgerGrows OP t1_it7r71v wrote

Is that the ufo looking thing ?

2

Talusen t1_it7s7z4 wrote

Yep.

1

HoneyBadgerGrows OP t1_it7sfc3 wrote

How do I inspect that? Just ensure it’s clear around it, or pull it off and look underneath/in it?

1

steve1186 t1_it7wppx wrote

Make sure you can move it up and down with very gentle force. If the water level is below the bottom of the float, add some water to make sure it rises.

3

TheFishBanjo t1_it89c85 wrote

So many possibilities --

  1. The pipes around the trap under your sink are partially blocked. Mine were full of cabbage once!

  2. Debris has gotten passed the screen into the sump area, partially blocking flow.

  3. The drain line from the dishwasher is plugged up with some gunk. I had that one my washer but it could happen to a DW.

  4. The impeller on the pump motor is having some trouble. Either gunked up -or- the impeller has become loose on the motor shaft -or- motor isn't spinning full speed.

That would be my order of attack. For the last one, I take the dishwasher out and lay it face down on the floor on a blanket to access the equipment on the bottom.

2

brock_lee t1_it7oksu wrote

The usual thing is a partially clogged sump. You say you took it apart. Did you remove the sump cover and get down in there and clean out any gunk? It can be difficult since there's usually not lot of room.

1

HoneyBadgerGrows OP t1_it7r32n wrote

Yes I took it apart completely drained with a siphon and scrubbed there was nothing down there I could see that would obstruct drainage - I was inside of it for about an hour

1

domdogg123 t1_it7puur wrote

Brand/model?

Check the air gap by the sink (it gets clogged)

1

HoneyBadgerGrows OP t1_it7qz00 wrote

Whirlpool quiet partner II- is that the skinny tube connecting to the sink pipe?

2

ripgressor1974 t1_it7s3jf wrote

Yes, some need to be vented or have a high loop as shown in this picture. https://ggrhomeinspections.com/wp-content/uploads/2021/04/high_loop-300x266.jpg

2

HoneyBadgerGrows OP t1_it7tq01 wrote

1

ripgressor1974 t1_it7uoma wrote

Sorry, can't do imgur here at work.

1

HoneyBadgerGrows OP t1_it7utmz wrote

No problem- just a pic of mine- it is not clogged, I did notice when I brought the hose up to where it would be a high loop some water did come out

1

ripgressor1974 t1_it7xq3k wrote

For sure find a way to add the high loop to your drain hose.

I had an issue recently with my dishwasher not draining at all. I ended up taking the hoses off the pump (underneath dishwasher) and found some grapefruit seeds that had got past the filtering stuff inside the dishwasher somehow and that combined with soap scum and/or grease finally clogged enough that no water would pass when the pump came on. It may be worth removing the hoses from the pump to look in them and the pump itself for clogging.

Good luck.

2

Ember357 t1_it7t7an wrote

My frigidaire unit had this problem a while back, traced it back to the instrument panel, it was shorting and stopping before the end of the cycle. It had other significant issues that pointed to it but not draining was the first indicator. Later on, it was not finishing cycles, starting without human input and then only the Heavy wash button would light up.

Got a used part off Ebay for 100 bucks because new parts were 8 months to a year out. ( mid pandemic).

1

reedstar1220 t1_it8039d wrote

It is possible that the micro switch below the ufo may be dislodged from the clip that holds it in place. This happens when little kids play with the ufo thingy lol

1

jakkarth t1_it88klq wrote

Your submission has been removed for one or more of the following reason(s):

  • Your question does not include the research you've done to find an answer yourself, or why that research didn't answer your question.

This is a basic requirement so others do not spend time repeating your steps. It is not a judgement about your question being "too easy." We're looking for evidence that you've made an attempt yourself.

  • Please do not use /r/DIY as your first stop for questions - we are not Google.

  • Please search Google and /r/DIY to see if your question has been asked before. Check owners manuals, tech support forums or contact the manufacturer.

  • Have you already done some basic research and are still stuck?

  • Please include what research you have done in your question so that others do not repeat your steps.

  • Consider posting your question in the sticky thread at the top of the subreddit.

  • Ask your question in our Discord server in the appropriate channel.

Please read our Full Sub Rules before resubmitting.

If you believe this was a mistake, please message the moderators.

###Do not respond to this comment - you will not receive a response.

1