Submitted by thrwaygrdn t3_z17pzz in DIY

Hello!

So I’ve finished insulating the walls of my summer house with kingspan, and now I’m moving on to the loft (it’s a single story) pitched roof. I had a lot of kingspan left over, so I was planning to cut kingspan tight and put it between the truss joists, then plasterboard tight underneath and put floorboards on top so that I can use the loft for storage. I’ve read though that doing so could lead to the joists sweating and rotting over time, is that true?

See photo below:

https://i.imgur.com/OcqzFS0.jpg

1

Comments

You must log in or register to comment.

minesskiier t1_ix9klom wrote

The sweating and rotting would come about because a moisture barrier is blocking moisture from escaping. It's got nothing to do with the Kingspan. Feel free to add as many as you need or want. Do you live in a humid environment ? In Colorado, I'd never worry about is as I live in a very dry environment .

2

thrwaygrdn OP t1_ix9mgi3 wrote

So plasterboarding tightly underneath and putting floorboards direct on top should be fine? And I’m from the UK, I tried the UK DIY sub but only received some vaguely related replies and not what I was looking for so I thought I’d check this sub. Lots of rain where I’m from, all year through ha.

Thanks for the reply!

2

minesskiier t1_ix9muk7 wrote

I think I'd call up one of your local insulation companies and ask for guidance. I'm guessing you'll be good, but moisture is a serious issue and getting your layers wrong can cause problems.

1

Horsiebox t1_ix9ph9a wrote

Make sure the insulation is not the full depth of the truss, so when you put the floor down, air can flow over the insulation. You attic needs to be ventilated.

1

ProfessionalPain4827 t1_ix9q05c wrote

You should use vapour barrier tape (e.g. alu tape) over the gap between insulation and wood to elimitate moisture migration from the inside. On top, on the other hand, the more vapour open the construction is, the better. Full timber floor boards wil be ok for this. OSB would not be ok (it cannot absorb or transport moisture).

If the roof on top is insulated, the moisture problem is already largely mitigated, but a vapor barrier from the inside is always advisable in the UK climate.

1

Mr-mgoo t1_ix9q94s wrote

If it was a normal cold roof attic you would need ro ventilate the loft space above the insulation to remove any moist air. If it's a summer house and you don't make any moisture you may be OK. It's the moisture from showers and dishwashers that xreate moisture In our houses, no so much an issue I outside buildings without steam in them, it might still be worth ventilation the space above the Insulation though, and try and make the ceiling air tight with a membrane.

1

thrwaygrdn OP t1_ix9r1z1 wrote

Unfortunately the insulation is the full depth of the truss. I guess I could put battens over the truss to basically make a raised platform for the attic floor so that air can then get underneath and to the kingspan, but is it still fine with the plasterboard tight against it underneath? Thanks a lot for your response by the way, much appreciated

1

thrwaygrdn OP t1_ixbcp3s wrote

The roof itself is felt (membrane) & battened, so I think that’s fine? I am considering putting a wood burner in this summer house though, so I think that could potentially introduce vapour issues — or is that incorrect? Thanks

1

jonny24eh t1_ixbgln8 wrote

Huh, TIL that not only is Kingspan not only not just the name of a rugby stadium, it's product that's so common as to be generic.

1

Mr-mgoo t1_ixc5hoe wrote

I'm not sure that a wood burner would introduce water vapour, you need to speak to the underlay manufacturer. Call their technical department and explain the build up.

1