Comments

You must log in or register to comment.

hbigmike1 t1_ixs5gyk wrote

I would wash the deck first. What will be removed is dirt, grime and any residue that lay on top of the deck. If not removed then the sandpaper would “load up” that much quicker and make for sanding just that much more difficult. Washing and or pressure washing is an easy step to take both before and after sanding…good luck.

265

alohadave t1_ixsx32x wrote

> Washing and or pressure washing is an easy step

Just give it several days for the wood to dry. Pressure washing especially is going to soak the wood. It's the same reason you don't seal a deck for at least a week after pressure washing it.

82

Texan2020katza t1_ixt4cc5 wrote

Less gunk makes the $andpaper last longer. So yeah, wash it.

12

[deleted] t1_ixs8od1 wrote

[removed]

86

[deleted] t1_ixsdzzc wrote

[removed]

55

Suffot87 t1_ixs5ey5 wrote

I would wash it before you sand it. Removing loose particles and dirt/grime will greatly extend the life of your sandpaper and prevent any of those particles from getting embedded and and messing up your deck.

64

Coal_Morgan t1_ixsxuvp wrote

Plus washing it will get into grooves, nicks and notches that sanding won't get into.

The gunk in notches will stain differently or not allow the stain to penetrate.

18

redw000d t1_ixsxpaw wrote

a friend 'sanded' his redwood deck. so, the nail heads, become iron filings, thus, Blackening his deck.. just for your info...

19

Bergwookie t1_ixtu7zh wrote

If you have sanded down to the nail heads, you can fix this, although with a lot of work... You take a punch and hammer and give every nail a beating

You'll feel every vertebra for at least a week, but by driving the nails a bit further in, you gain a bit more ''flesh'' for future sanding, afterwards you take the sanding dust, mix it with wood glue and fill the holes.

The same procedure like on long board wooden floors indoors.

Incredible amount of work, but way better than ugly iron stains or a nail ripping a nice groove in your bare feet (and now nice blood stains in the wood) ;-)

Check from time to time if nails work themselves up, wood is constantly ''working'', so nails tend to come out over time, if they become loose, pull them, put matches with wood glue in the hole and hammer the nail back in.

Or you go completely for larch or Douglas fir for your next deck, those don't have to be sanded/stained, as long as the underconstruction is well made, so the wood can dry completely, the wood gets grey but doesn't rot. Such decks can last up to 100years if done properly (proper ventilation, groves between the boards, not mounted directly on concrete, no always shady places, nails/screws out of stainless steel).

3

rbundy t1_ixs7odf wrote

If redwood or a similar soft wood, I would suggest washing it after sanding using a broom and oxygen bleach, then rinse well. Pressure washing is very hard on the wood fibers and will prematurely degrade the surface.

10

SapphireDesertRosre t1_ixsqbq8 wrote

No matter what the question is, the answer is always yes. Wash it.

10

oldmanartie t1_ixsot6e wrote

Depends on the wood maybe, but a quick wash with a mild detergent to get any oils off that would cause the stain not to adhere would be wise. This will pull stuff up out of the wood that sanding wouldn’t (woodn’t).

9

sbsb27 t1_ixt68jl wrote

In the Pacific Northwest - cedar deck: Every year clean...packaged mildew solution or diluted bleach. Protect your plants. Scrub with a stiff bristle push broom. Rinse. Let it dry. Touch up/re-apply deck finish as needed. Then, every 2 years, mildew treatment then strip the old finish - that stiff bristle push broom is the ticket. No pressure washing - raises the grain. Refinish. And every 7, 9 years (climate dependent) mildew treatment and strip - then mechanically sand (ok, 9 years) and re-stain/refinish. Yes, a cedar deck is work...and beautiful. I had a cedar deck for 25 years in a temperate rain forest, replacing three boards due to mildew damage. No maintenance, no deck!

5

604_heatzcore t1_ixsn7h0 wrote

Depends. If u wash it its gonna get wet... n u gotta let it dry if u live somewhere hot I'd do it but if it's winter or cold I'd just blow it down or sweep it

2

Liesthroughisteeth t1_ixsptjn wrote

If it's not finished and reasonably clean why bother. I'd be more inclined to wash it after sanding, but a day or two before refinishing (depending on the weather). :)

2

Jagbag13 t1_ixswxjm wrote

I refinished my deck this past fall. I power washed the deck and would highly recommend it. Not only did it remove most of the old paint/stain, it also removed a ton of dirt and debris that otherwise would have ended up reducing effectiveness of sanding.

2

Tasker2Tasker t1_ixsn7pm wrote

Need to? No.

Does it benefit the overall process? Yes. The sequence below maximizes benefit and outcome, under most conditions.

Knowledgeable word care/restoration folk would either strip or clean, then brighten with oxalic acid, then allow to dry. Then sand (40 grit for aggressive removal, 60 for moderate, finish with either 80-100, fairly pointless/counterproductive to go above that for decking without knowing precisely why) and stain.

1

JadaNeedsaDoggie t1_ixswzqw wrote

When you sand with a much higher grit, you're closing the pores in the wood (which is why it feels smoother) and the stain/water repellent won't penetrate as deeply and won't last very long, especially with foot traffic. I have a cedar deck and stop at 80 when I refinish about every 3 to 4 years.

4

navigationallyaided t1_ixt31wc wrote

Wash it with Dawn, Clorox Outdoor formula or deck wash(Behr, Olympic, Zinsser, Ben Moore - doesn’t matter which brand for cleaner). If water beads, you have wax or grease on the deck and that must be addressed.

If Thompson’s Water Seal was ever used, you must scrub the deck with ammonia to remove the wax.

1

chopsuwe t1_ixtxcki wrote

Come on, the joke wasn't even that good to start with. Surely you've got something better to do with your life than repeating the same joke for the hundredth time.

1

moralesnery t1_ixt16bo wrote

It's not obligatory, but power washing it will remove dust, dirt, some mold.

I would just try to use as little water as possible, do it when the sun is out so it can dry faster, and then sand it.

And after sanding it I would clean it using paint thinner or at least alcohol.

0

paddywawa t1_ixs2wrt wrote

You can google this as there is a lot of sites with great advice but I believe it’s a very good practice to wash after sanding. It will get rid of dust and brighten the wood.

−10

jeffroddit t1_ixsaxfw wrote

Doesn't it raise the grain and kinda anti-sand it though?

3

pbandnv1 t1_ixsxxpc wrote

Yes. After sanding just blast it all clean with an air compressor to get rid of the dust. Then stain and seal. Never wet it after sanding.

5