Submitted by mofankri t3_yc3v0p in headphones

I'm a newbie in audio world. From what I know, audio device with planar driver demands higher power, but how to determine the requirements to drive certain devices? Some say look at the impedance, vrms, or the mW.

I've read the faq and it says only about the impedance in ohm. Is it the only factor? Since certain dac have different mw or vrms for the same 32ohm

Right now I'm using tin t3+ with dynamic driver which easy to drive. My DAC dongle is Jcally jm20 with cirrus logic cs 43131 chip. I'm planning to buy either dioko or p1max or stellaris, which all are planar. I think I will buy the DAC dongle first since it will increase the quality of my t3+ either way.

2

Comments

You must log in or register to comment.

Miller_TM t1_itk9bzn wrote

Like 99% of IEMs will run on anything, even the somewhat power hungry Truthear Zeros.

10

Hyurakun t1_itlwj4a wrote

Truthear Zero are power hungry? I thought they were one of the most easily drivable IEM.

1

Miller_TM t1_itmif2p wrote

The specs on the box are misleading, before on my volume knob with Moondrop Chu I could barely use 20% volume, well with the Zeros I can crank it up to 80%.

1

audioen t1_itkhotf wrote

Typically, you need to know at least two things to evaluate power. The impedance controls the overall voltage level needed to put in enough milliwatts in to the headset as function of voltage, P=U²/R, and you are probably best off looking up the actual impedance measurements rather than using some single nominal value given by manufacturer. It is also of interest whether the impedance varies by frequency, and if so, by how much. The other is, what sound level is achieved per milliwatt of power, or per 100 mV of driving voltage from peak to peak, or however they prefer to express it.

Power requirements of headsets are generally low in context of the systems that are tasked at driving them. From what I have seen, the range is somewhere from less than 1 mW to about 30 mW for something like 96 dB SPL which should be loud enough to cause hearing damage if prolonged. I am not sure if there is use case for having much more loudness than this, but watts multiply very quickly when target SPL goes up given that this scale is logarithmic, but on the other hand, so does driver excursion and thus distortion. Many headsets are operating close to their maximum performance at 96 dB and usually only magnetoplanars and electrostatics can handle more SPL without distortion going out of control.

If the impedance of the headset is low, it should work perfectly with the $10 Apple USB-C DAC dongle, as this particular one provides low-impedance output at mere 0.9 ohm, which is exceptionally good, and has been measured to be capable of supplying 33 mW of power to a 32-ohm load before distortion. (The issue with high output impedance is that it adds a frequency-varying component which distorts frequency response if the headset's impedance also varies as function of frequency.)

The other issue is whether it gets loud enough for you. This is question of providing high enough voltage to drive the headset. This can be a problem with high impedance headsets, as they tend to require much larger driving voltage because their large internal resistance forces the power to be very low until something like full volts are hit. For instance, if your headset had 600 ohms impedance, and it takes a milliwatt of power to drive the headset loudly, you need to provide something closer to a 0.8 V (P = U²/R = 0.8 V * 0.8 V / 600 ohm = about 1 mW), whereas most low-impedance headsets are already very loud at mere 0.1-0.2 V output voltages.

I personally go by audiosciencereview's measurements as they typically add each headset to their list they put on every review and show the millivolts needed to reach 96 dB benchmark level. Some low-impedance headsets like Hifiman HE6SE v2 with 64 ohm impedance actually require over 1V before they get loud, so it can be said that some planars are very inefficient, but even that is relative to other headsets, as it is still a few dozen milliwatts, similar to the power requirement of a single standby led you see all over the place. Most are not that bad. So the summary is probably that you can simply try driving with the Apple USB-C DAC dongle first, and if it is not getting loud enough, then get something else with more output voltage.

5

atyne_mar t1_itk9sif wrote

>audio device with planar driver demands higher power

That's not always the case. For example, Avantone Planar is very easy to drive.

>how to determine the requirements to drive certain devices

You have to find out how much power/voltage your source provides at the headphone's impedance. That's not always easy to find out as manufacturers usually specify only the power at a few standard impedances. Or they don't mention it at all.

When you know the power/voltage, you can use the power calculator to find out how many dB can it push. 110dB is considered the minimum to drive headphones loud enough even with the HDR content.

But that's only speaking about power. At the end of the day, power is only loudness. There are other things that determine audio quality and you can't just read them off the specs.

2

dimesian t1_itm3hkf wrote

The sensitivity is the most important factor, a high impedance pair of headphones can be easier to drive than a pair with low impedance if the sensitivity is high enough. Very few IEMs need more power than the average phone headphone socket puts out, I can only think of a handful, the Final e5000, Tin P2 are among them. I don't know why so many people only consider the impedance though, some headphone reviewers and retailers also overlook the sensitivity and a few only list the impedance in the specs.

IEMs almost always have very low impedance so you need only refer to the sensitivity.

1

szakee t1_itk813f wrote

a dac doesn't power anything. A dac converts. an amp powers.

0

mofankri OP t1_itk9ezy wrote

Yes that's what I meant. Usually dac dongle comes in pair of dac/amp

1

atyne_mar t1_itk9zbc wrote

That's incorrect. DAC provides power. Amp only amplifies it. If you use a proper DAC with 2V output to power an amplifier, you'll get more power than feeding it off the Apple Dongle for example.

1

szakee t1_itkaptt wrote

but you won't really connect a hp straight to your dac.

0

mofankri OP t1_itkb6en wrote

I thought DAC dongle could be plugged directly to handphone? Or to laptop which has type c port (if the dongle has type c port)

2

szakee t1_itkbeiq wrote

a dongle is different to a standalone DAC which has RCA outputs.

0