Submitted by KapToIIIe4Ka t3_10m37ha in headphones
Pretty much the title, I want to buy them, but I don't have neither amp nor even dongle. I calculated necessary power on https://www.headphonesty.com/headphone-power-calculator/ and it tells they'll play fine, bit I kinda doubt it. Please, any thoughts?
Apple says their computers output up to 3 Vrms to high impedance headphones. If it was 1 Vrms (the Apple dongle’s power level) I’d say that’s borderline, you might benefit from more headroom, but 3 is tons of power.
it’s only the new ones, M1 Pro/Max and M2
Fair enough, I didn't see OP specify the year of his model, and was too lazy to search beyond the first article I found, on the contingency that he might have had an older model.
it will work good enough but is not ideal when getting the most out of the headphones. if you have the new updated macbook air with the m2 chip, then that should be very well off
OP Please listen to this comment. Being able to power, and properly drive are two different things. The 600/650(6xx) all greatly benefit from a good amp (which you can get for around $100 these days) due to their impedance curve.
An apple dongle will be enough (without EQ)
No, Apple dongle is not sufficient. 97 dB at 300 ohm requires 20mW to reach 110 dB SPL (for peaks and transients), or 7mW to 105 dB SPL (in the very best case where someone listen to low volume and compressed music).
Apple dongle is measured to be 3.6 mW at 300 ohm. This is 2x short for 105 dB and 5x short at 110 dB.
“Sufficient” is a question of what you listen to and how loudly. My normal listening level with loudly mastered music is about 75db peak spl and I can’t remember the last time I needed more volume than what a dongle could drive into the HD600s.
Don't confuse average with peak. There are easily 20-30 dB of dynamic range in the music. And can be more for audiophile recordings. If you are listening to peak SPL 75dB, then your average SPL is like 45dB, which is very unlikely.
Most people are listening to 65-85 dB average, with peak SPL reaching 105-115 dB. That is why power calculators defaults at 110dB.
https://www.audeze.com/blogs/technology-and-innovation/sensitivity-impedance-and-amplifier-power
I have measured 100mV on the output when playing 500hz sine wave on my HD600 at my normal listening volume. That's should be around 85dB as the sensitivity is 104 dB @ 1V.
The peaks can't be higher than 85db as my volume knobs limits the output to 100mV.
Maybe I'm just listening to very low volumes.
(Edit: Based on follow-up post below, updated calculations based on actual sensitivity and corrected for dB/V)
So I went ahead and looked up HD600 spec: https://www.sennheiser-hearing.com/en-US/p/hd-600/
So your numbers do not the spec of the headphones.
In any case, the comment below doesn't change. Assuming your setup can output 85 dB peak, then if you listen to average SPL of 55 dB SPL or less, and assume the dynamic range in your music is 30 dB. Then you are good. Your peaks will only reach 85 dB SPL.
On the other hand, if you are at 65 dB SPL average, with 30dB dynamic range in your source, then your peaks should be at 95 dB SPL. And if your device can drive to 85 dB, then some of the peaks will be clipped. It can be hard to tell when music is slightly clipped. Like 90-95% of the sound is there. It will sound slightly compressed (less dynamic) because the max levels are cut off.
95% of the headphones have no issue with power with most amps. So people will say power is BS and there is no such thing as lack of power. But there are outliers. Some people listen to loud music. Some music recordings have high dynamics. And some headphones do require Watts of power (e.g. Susvara, HE6se).
You got mixed up in sensitivity units: 104dB/V (not dB/mW) adds up to 84dB @ 0.1V, not 89.
So basically, 104dB/V means 104dB SPL peak with the 1V maximum output of the Apple dongle. Isn't this loud enough? I personally use 108dB/V IEMs with my Apple dongle and never set the volume above -20dB (otherwise it's just too loud for me) so that's 88dB SPL peak. The HD600 would still have 16dB of headroom at my listening level. So from a theoretical standpoint, it looks like the Apple dongle could drive the HD600 loud enough, at least for some people? Am I missing something?
Thanks for the correction. So I went ahead and looked up HD600 spec: https://www.sennheiser-hearing.com/en-US/p/hd-600/
Apple dongle is 3.6mW or 1V at 300 ohm. No, Apple dongle is not sufficient, for most people listening to 75-80 dB with 30 dB dynamic range.
According to a few posts the official specs on Sennheiser's website are wrong (lol) and the actual values would be 97dB/mW and around 102-104dB/V. I don't own the HD600 and have no skin in the game, but looking at the numbers it seems they would be more than loud enough for me with an Apple dongle. I mean, my current setup is loud enough despite Android limiting the volume of the Apple dongle to -20dB (0.1V) so I really don't need 110dB peak... But if you do, that's fine too! 👍
DACoid detected, opinion rejected
Probably. My old 2014 MBP with ~1.3V full-scale output on the HP jack drives them plenty loud for my needs. I think the newer macbooks have better headphone outs.
How do you calculate it tho? I mean, how do you know MacBook Air's output power? I have the M1 Air and this might come in handy.
I've used use an M1 Macbook air and my HD6xx (650s) which have the same impedence and sensitivity and I had plenty of headroom, though that probably depends on how loud you like your music. I tend to listen to more modern music which is louder than say classical music.
Try the HD660S. It’s half the impedance, much easier to drive.
Yes. A phone can drive them.
Yep
Yes
Clickbaitllama t1_j60vh9q wrote
The calculator doesn’t lie.